Just How to Remove as Well as Change a Tub
Just How to Remove as Well as Change a Tub
Blog Article
What are your ideas on A Step-by-Step Guide to Installing a Bathtub?
Mounting a bathtub isn't precisely brain surgery, yet it does require solid plumbing, woodworking, and also sometimes, tiling skills. Replacing an old bath tub with a brand-new one is also a moderately tough task. If the old bathtub is readily available, the job can relocate easily; if you need to open up a wall to remove the old tub as well as place the brand-new bath tub, the task is much harder. In either case, the job is within a house handyman's abilities, although you will certainly require a helper to move out the old tub and set in the new one. Make sure you have certified on your own for the work and also fit trying it. Instead of hiring a service provider to take control of a halfway-completed task, it is far better to think about utilizing one before you begin. Chances are you might require an expert plumber to make tube connections.
This short article will aid you mount a brand-new bathtub in your bathroom if you have currently gotten a new tub and do not require to change the setup of your previous water system pipes.
Your tools and also product checklist ought to comprise the following:
Planning for the Setup
Firstly, the sustaining framework supplied with the bathroom must be fitted (if required) according to the manufacturer's guidelines. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is very important to ensure that if the faucet includes a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the taps unit to stop strain on the tub.
Fit the flexible faucet adapters to the bottom of the two faucets using 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Make certain you make use of all of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath must currently be ready to be suited its final setting.
Removing Old Touches
If you need to change old faucets with new ones as a part of your setup, after that the first thing you ought to do is separate the water supply. After doing so, switch on the faucets to drain any type of water continuing to be in the system. The process of eliminating the existing faucets can be quite troublesome as a result of the limited access that is commonly the case.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipelines to the taps. Have a cloth prepared for the continuing to be water that will come from the pipes. Once the supply pipes have been eliminated, utilize the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this procedure. Once the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any old sealing substance.
Prior to going on to fit the brand-new taps, compare the pipe connections on the old taps to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Installing the Bathtub
Using the two wooden boards under its feet, put the bath tub in the called for position. The wooden boards are useful in uniformly spreading out the weight of the tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The following objective is to make certain that the bath tub is leveled all round. This can be achieved by checking the level and readjusting the feet on the tub up until the spirit level reads level.
To mount faucets, fit all-time low of the furthest flexible faucet adapter to the proper supply pipeline by making a compression join; then do the same for the other faucet.
Activate the water as well as inspect all joints as well as new pipework for leaks and tighten them if necessary. Load the bath tub as well as likewise inspect the overflow outlet and the normal electrical outlet for leakages.
Lastly, repair the bath paneling as described in the supplier's user's manual. Tiling and securing around the tub ought to wait until the bath tub has been used at the very least once as this will resolve it into its last placement.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will certainly need a plastic port to prevent damage to the string. One end of the port fits on the plastic tail of the tap and also the various other end offers a link to the current supply pipelines.
If you need to fit a monobloc, then you will certainly need reducing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin guaranteeing that the washing machines are in area in between the faucet as well as the sink. Secure the faucet in position with the maker offered backnut. Once the faucet is safely in position, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with normal faucet connectors. The previous type needs to be linked to the faucet finishes first, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the location where the bathroom satisfies the floor tile, it is necessary to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to split an inflexible seal, causing the water to pass through the wall surface between the bathroom and the tiling, resulting in difficulties with moisture and also possible leakages to the ceiling below.
You can pick from a variety of coloured sealers to assimilate your fixtures as well as installations. They are sold in tubes as well as cartridges, and also are capable of sealing voids up to a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with twists of drenched paper or soft rope. Keep in mind to constantly fill the tub with water prior to sealing, to enable the activity experienced when the bathtub is in usage. The sealer can crack relatively early if you do not think about this activity before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise conveniently readily available on the market. It is a good idea to fit the floor tiles using water-resistant or water resistant sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a serious reader about Installing A Bathtub, I think sharing that excerpt was really useful. I beg you take the opportunity to share this entry if you enjoyed reading it. I love reading our article about Tools You Need to Install a New Bathtub .
Request An Appointment
Report this page